Register FAQ Community Calendar Today's Posts Search
Go Back   ScootDawg Forums > Media :: Reviews :: Classifieds :: General > General Scooter Discussion
Reply
 
Thread Tools Search this Thread Display Modes
Old 08-19-2018, 09:35 PM   #1
Mattr59   Mattr59 is offline
 
Join Date: Aug 2018
Posts: 5
Don't understand - makes no sense

Ok, I do not understand this.

I have spark, I look at the removed plug and I see sparks. Replaced the plug anyway, in case it has a crack or something. Spray in some start fluid - nothing not one pop. Inspect the magneto, the pick up is in the correct spot. Did not check compression but from the sound of the starter, it has compression.

I was on my way home from work and the belt broke. Engine kept running, in fact, it ran well. Pulled the clutch and the variator installed the new belt. After that, it would hardly crank over. shorting the relay did not help so I ordered a new starter motor. That seemed to help, but it still cranks hard which makes no sense.

150cc Jonway

Does anyone have any ideas?



Login or Register to Remove Ads
  Reply With Quote
Old 08-20-2018, 05:19 PM   #2
rks   rks is offline
 
rks's Avatar
 
Join Date: Dec 2013
Location: Western New York
Posts: 454
Could the rollers/sliders have gotten cockeyed when you put the variator back on while installing the new belt. If this problem started right after new belt...I'd start by pulling the cvt cover.
__________________
2011 Jonway 150cc..16,109 breakdown free miles, and counting

  Reply With Quote
Old 09-05-2018, 10:20 PM   #3
Mattr59   Mattr59 is offline
 
Join Date: Aug 2018
Posts: 5
Thanks for the reply, sorry for not getting back sooner. I think I figured out what went wrong. I think the CDI was intermittent. While replacing the belt it was sitting and the battery ran down. I put it on a car charger. A friend of mine said that a car charger will ruin the CDI. A week or so later when I rechecked it now had no spark.
I've ordered a new CDI, but too much has been going on with other cars in the house.

Has anyone ever heard this? That a car battery charger will ruin a CDI? The friend said a trickle-charger will not harm it, only a large-capacity car charger.



Login or Register to Remove Ads
  Reply With Quote
Old 09-22-2018, 07:06 PM   #4
Mattr59   Mattr59 is offline
 
Join Date: Aug 2018
Posts: 5
Ok, I am still dead in the water. Absolutely no idea.

The Stator puts out 30 to 40 volts (AC). I have replaced the CDI and the coil with two different other units - I have now replaced the trigger coil too. I buzzed all the wiring, I redid some bad-looking connectors, I removed the grounds and cleaned them all up.

I am really desperate! What the hell could it be? Why no spark?

It's like this thing is defying physics just to piss me off.
  Reply With Quote
Old 09-22-2018, 08:56 PM   #5
Roscoe   Roscoe is offline
 
Join Date: Nov 2016
Location: N. of Texas and S. of Kansas
Posts: 252
Here ya go ... step by step .... https://www.buggydepot.com/tech-cent...uide-no-spark/



Login or Register to Remove Ads
  Reply With Quote
Old 09-26-2018, 10:34 PM   #6
Mattr59   Mattr59 is offline
 
Join Date: Aug 2018
Posts: 5
I've done everything in that (and other) guides. I give up. I'm selling it on Craigs list.
  Reply With Quote
Reply

Tags
150cc, gy6, jonway


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:40 PM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.